Слив с функцией осаждения песка 7070T Kavika на ножках 480х330х120 мм
Бренд:
Единица: шт
Время доставки: 14-21 день
Попробуй промокод PEGU-KEVAD! Выбери товар по полной цене, добавь в корзину, и введи код купона при покупке! Время работы промокода ограничено!
Liivaeraldusnou Kavika jalgadel 480х330х120 мм
Liiva settimise funktsiooniga drenaažid 7070
Сливы с функцией осаждения песка 7070
Назначение данного слива – препятствовать попаданию песка в канализационную систему. Данный слив устанавливают в моечных помещениях рядом с моечной раковиной, также через слив 7070 пропускают сточный шланг от стиральной машины.
Внутренняя, съемная часть слива служит для осаждения песка и грязи, она легко отделяется и моется. Вода поступает в слив через шланг, устанавливаемый в отверстие крышки слива. Отвод воды осуществляется через сливной патрубок DN32, который присоединяется к канализационному трапу.
Внешние размеры 480х330х120 мм Внутренние размеры 300х280х115 мм
Слив с функцией осаждения песка 7070 изготавливается с ровным плоским дном, что даёт возможность устанавливать его на нижнюю полку стола-мойки, под раковину.
Сливы с функцией осаждения песка 7070/T
Слив с функцией осаждения песка 7070/Т оснащается металлическими ножками, в остальном конструкция аналогична вышеописанной. Ножки имеют регулируемые по высоте опоры, благодаря чему Слив легко устанавливается на неровном полу.
Sand separator basin 7070
The sand separator basin is intended for preventing sand from entering the sewer network. Sand separator basins are used in cleaning cupboards in connection with washbasins.
The detachable inner basin serves as the actual separator basin that is easy to empty.
The supply water pipe is led into the basin through the hole in the cover, and the discharge pipe, DN32, is connected to the floor drain.
Outer dimensions 480x330x120 mm
Inner basin 300x280x115 mm
The sand separator basin 7070 comes with a flat bottom, which makes it possible to place it on the washstand’s lower shelf below the sink.
Sand separator basin 7070/T
The sand separator basin 7070/T is equipped with low legs; in other respects the structure is similar to the model described above. The leg adjustment pads make it easy to place the sand separator basin in a room with a sloping floor.
FM Mattson незамерзающий садовый кран 400мм, с ключом ХОЛОДНАЯ+ГОРЯЧАЯ вода
Garden valve for cold and hot water
- For cold and hot water
- With approved non-return valves
- Can be cut to suit wall thickness
- Wall bracket: H=70 mm, W=180 mm, screw holes c/c 164 mm
298,90 €
Автоматическая мойка для сапог с дюзами, 12V, 50Hz
automatic washing system for wellingtons with jets - 12V, 50Hz
Radius of sensor | 0 – 0,4 m |
Water inlet | G 1/2“ |
Water pressure | 0,3 – 1,0 MPa |
Outlet | d = 32 mm |
Inner dimensions of the trough | 250 x 400 x 280 mm |
Electricity protection | IP 55 |
Power supply | 12 V, 50 Hz |
Power requirement | 10 VA |
Source of power supply | ZAC 1/20 (max. 2 x AMO 01) |
ZAC 1/50 (max. 5 x AMO 01) | |
Weight | 18 kg |
- Set up water inlet as per picture
- Set up outlet d = 32 mm
- Set up cable for power supply – 12 V, 50 Hz from source of power supply ZAC
DESCRIPTION
1037,00 €
> Working pressure : 1 to 5 bar
> Flow : 6 l/min at 3 bar - 4-position flow adjustment device Anti-water-hammering design
> Flow time : 15 seconds (± 5 sec.)
> Hydraulic supply : In-line water inlet M G 1/2" Inlet and outlet Cold water
> Thermal resistance : Resistant to a temperature of 75°C for 30 minute thermal shock
> Security : Patented anti-blocking "S" system to avoid the water to flow continuously
> Delivered with : 1 Cross-partition control (1 to 200 mm thick) 1 Short wall spout (Non-rotating fixing) 87 mm 1 Closing tap with S anti-blocking system 1 stop valve M 1/2" (15x21) / M 1/2" (15x21) with quick couplings (12x14 mm) Instruction manual
> Standards & approvals : Brass body in accordance with EN 1982, EN 12164, EN 12156 Molded chrome-plated body in accordance with EN 12540 200-hour neutral salt spray resistant (NSS) in accordance with ISO 922
Semi-recessed QUADRA washbasin
Ref. 120650
Semi-recessed washbasin, 380x380mm.
Suitable for use with wall-mounted or extended mixer/tap.
Basin internal diameter: 310mm.
Cutout diameter: 310mm.
Stainless steel thickness: 1.2mm.
Polished satin finish.
Stainless steel thickness: 1.2mm.
One-piece, seam-free pressed bowl.
Rounded edges prevent injury.
Supplied with 1¼" waste.
Without overflow.
CE marked. Complies with European standard EN 14688.
Weight: 3kg.
TECHNICAL FEATURES
Semi-recessed QUADRA washbasin
Ref. 120650
Height | 130mm |
---|---|
Length | 380mm |
Width | 380mm |
Thickness | 1.2mm |
Finish | Polished satin 304 stainless steel |