Категории

Delabie GROUP термостатический вентиль 1" PREMIX COMFORT 90L 32°C to 42°C

Артикул: DE-731003
Бренд:
Единица: шт
Время доставки: 14-21 день
Цена:
1031,00 €
Кол-во: - +
   - или -   

PREMIX COMFORT 
Ref. 731003

Group thermostatic mixing valve for mixed water distribution from 32° - 42°C: 
Anti-scalding safety. 
Regulates temperature variations. 
Filters and non-return valves can be accessed from the outside without removing the mechanism. 
Thermal shock with no specific lever needed (push-button on the control knob). 
Interchangeable cartridge with automotive cell.
High-resistance chrome-plated brass body. 
Maximum hot water temperature: 85°C. 
Differential hot water / mixed water: 15°C minimum. 
Pressure difference at the inlets: 1 bar maximum (0.5 bar recommended). 
Minimum pressure / maximum: 1 - 10 bar (1 - 5 bar recommended). 
Left hand side hot water inlet (red ring) and right hand side cold water inlet (blue ring). 
Mixed water outlet at the top (purple ring). 
For bottom outlet: unscrew / place lid at the top and outlet connector at the bottom. 
Maximum temperature limiter, can be adjusted by the installer. 
Reduced risk of scalding by limiting temperature at the point-of-use. 
90 lpm - M1".

Файлы

Схожие продукты
Артикул: P30302 ,   Время доставки: 7 дней
79,20 € (10%)
88,00 €
 
 

AUS 11

Pressure button-controlled shower for heat regulated water

 

 

   
 
 
 

AUS 11 is a new type of shower fitting for single shower control. The fitting is designated for premixed water – with one water inlet and shower outlet elbow. Water is released and closed by an anti-vandal pressure button connected to electronics and an electromagnetic valve. The fitting is covered by a rust-free anti-vandal cover to prevent damage. 

The mounting system has been designed so as to make removing the cover without using tools impossible with no bolt or screw being visible. The cover can be "pushed into" the wall level even if the mount box has been walled to an incorrect depth. 

AUS 11 is identical to AUS 1P with a different design and very resistant cover sheet. 

Electronics can work in two modes: 

1) The button works on the START/STOP basis – water release/closing. If the water is not turned off upon the time adjusted by the user or manager (e.g. 20 seconds), the electronic system itself instructs water stopping. The user must press again to start water running. This significantly saves water as the user reduces the showering time. 

2) The button works on the START/STOP basis. After the time adjusted by the manager (e.g. 3 minutes) expires there is a forced break when water cannot be released. During this time, the user is forced to leave the shower or wait. This prevents needless showering – water wasting. 

 

 
Basic technical information
Water input: G 1/2“
Water pressure: 1 - 10 Bar (0,1 – 1,0 MPa)
Time of water flow: 10 s – 42,5 min in mode 1
  0 s - 42,5 min in mode 2
Power supply: 12 V, 50 Hz
Power requirement: 6 VA
Source of power supplz: ZAC 1/20 (max. 3× AUS 11)
  ZAC 1/50 (max. 8× AUS 11)
Weight: 2,0 kg
 
 
Requirements for setting up the construction
  1. Water installation set up as per picture
  2. Set-up alcove 150 x 75 mm for installation casket
  3. Set-up cable for power supply – 12 V, 50 Hz from source of power supply ZAC
 
 
Complete delivery
  • installation casket
  • input and output bolting
  • electromagnetic valve
  • spherical valve
  • covering metal plate with piezo button
  • electronics
 
 
Made to order
  • SP 1 – shower arm with water flow of 9 l/min
  • SP 2 – shower arm with water flow of 7 l/min
  • SP 3 – shower arm with water flow of 7 l/min
  • ZAC - source of power supply 12V, 50Hz
 
 
Figure
 
 
A - water inlet G 1/2"
C - electricity supply cable 12 V, 50 Hz 
G - water outlet into shower armG 1/2"
 
 
 
 
Download information about the product
AUS 11 data for projectants - ( 84 kB )
 
Артикул: AZP-AUS 11 ,   Время доставки: 3-4 недели
254,00 €

> Working pressure: 1 to 5 bar

> Flow: 3 l/min at 3 bars - 4-position setting Anti water-hammer system

> Flow time: 7 seconds - lever upwards 11 seconds - lever downwards

> Hydraulic supply: 2 PEX hoses DN8 G3/8'' - 350mm

> Thermal resistance: This tap can withstand a thermal shock of 75°C for 30 minutes as part of a thermal shock programme

> Safety: With S® antiblocking system to prevent blocking in continuous flow With temperature limiter (at 38°C for cold water at 15°C/3 bar and hot water at 60°C/3 bar) > Convenience: Soft-touch Two-coloured ergonomic lever, in glass fiber reinforced polymer

> Delivered with: 2 PEX hoses with swivel nut and NF check valves 1 base gasket 2 MM 3/8'' (12x17) stop valves 2 Filter gaskets 1 Fixing bracket

> Standards / Approvals: Chrome-plated brass body compliant with standards NF EN1982 / NF EN12164 / NF EN12165 Nickel-Chrome surface treatment compliant with NF EN12540 Neutral Salt Spray (NSS) resistant: 200 h according to NF ISO 922

Артикул: P68052 ,   Время доставки: 7-14 дней
293,00 €

> Working pressure :

1 to 5 bar

> Flow :

6 l/min with integrated flow limiter. Anti-water-hammering device Fixed rotating shower head with anti-limescale spikes

> Flow time :

30 seconds (± 5 sec.)

> Hydraulic supply :

G 1/2" (15x21), top or rear water inlet. For rear water inlet, we recommend to add the adaptation kit under the reference 91026 On P 50 tap NF II with cold water or pre-mixed water

> Material :

Anodised aluminium extruded section (2.5mm thickness) Aluminum removable valve plate, peinted RAL 7005 colour High resistance RAL 7005 coloured ABS covers

> Functioning:

Wide opening panel without the need to dismantle from the wall and shower taps on a removable valve plate

> Thermal resistance :

Resistant to a temperature of 75°C for 30-minute-thermal-shocks

> Security :

"Legionella" version: pre-equipped for PRESTO solutions
Non turnable push button. Non-removable, wear-proof red marker

> Delivered with :

1/2" hoses with revolving nuts
MM 1/2" (15x21) straight stop valves and 250 micron filters Fastening screws and instruction manual

> Standards & approvals :

Brass body in accordance with EN 1982, EN 12164, EN 12165 Chrome-plated surface treatment in accordance with EN 12540
200-hour neutral salt spray resistant (NSS) in concordance with ISO 9227

Артикул: P88824 ,   Время доставки: 14-21 день
835,00 €

PREMIX SECURITY 
Ref. 731054

Group thermostatic mixing valve for hot water circulating loops adjustable from 44°C to 58°C: 
Anti-scalding safety. 
Regulates temperature variations. 
Non-return valves and filters accessible from the exterior without having to remove the mechanism.
Thermal shocks are possible. 
Interchangeable cartridge with automotive cell. 
High-resistance chrome-plated brass body. 
Maximum hot water temperature: 85°C. 
Differential hot water / mixed water: 15°C minimum. 
Pressure differences at the inlets: 1 bar maximum (0.5 bar recommended). 
Minimum pressure / maximum: 1 to 10 bar (1 to 5 bar recommended). 
Left hand side hot water inlet (red ring) and right hand side cold water inlet (blue ring). 
Mixed water outlet at the top (purple ring) for bottom outlet: unscrew / place lid at the top and outlet connector at the bottom. 
15% energy savings: optimised heat loss (comparison between a circulating loop at 55°C and a non-circulating system at 70°C). 
Safety and prolongation of system life span (Hot water at >65°C leads to premature aging within the system). 
Maximum temperature limiter, can be adjusted by the installer. 
Reduced risk of scalding by limiting temperature at the point-of-use. 
140 lpm - M1 1/4 ".

Артикул: DE-731054 ,   Время доставки: 14-21 днь
1480,00 €