Категории
7130.jpg Zoom

Kavika ванна на ножках

Артикул: KAV7130
Бренд:
Единица: шт
Время доставки: 14-21 день
Цена:
1075,00 €
Kuumakse alates: 91,38 €
Кол-во: - +
   - или -   

Saappaidenpesuallas 7130

Saappaidenpesuallas 7130 on omilla jaloilla seisova allas, joka on suunniteltu käytettäväksi esim. päiväkodeissa kumisaappaiden ja kuravaatteiden huuhteluun sekä teollisuudessa hätäsuihkualtaaksi.

Tuote on kotimainen ruostumattomasta teräksestä valmistettu monikäyttöinen allas. Altaan reunat on pyöristetty turvallisiksi.

Altaan ulkomitat ovat 600x600x350 mm, sisämitat 550x550x250 mm. Allasta valmistetaan myös erikoismitoin.

Altaan mukana toimitetaan pohjaventtiili sekä pohjatulppa helmiketjulla. Altaan jaloissa on säätötassut, joilla se on helppo asentaa suoraan.

Схожие продукты

DESCRIPTION

MONOBLOCO S21 WC pan with cistern 
Ref. 110390

Floor-standing WC pan with dual flush cistern 3L/6L, 370 x 815 x 620mm. 
Bacteriostatic 304 stainless steel. Polished satin finish.
Stainless steel thickness: 1.5mm. 
One-piece pressed WC bowl, seam-free for better hygiene. 
WC bowl surface is polished with rounded edges for easy cleaning. 
Concealed perimetral flushing rim. Water supply can be recessed from below or exposed from the side (right/left). 
Recessed horizontal or vertical waste outlet. Supplied with PVC pipe. 
Pre-drilled holes for fixing the toilet seat. Supplied with stainless steel blanking caps when installed without toilet seat lid. 
Quick to install: 2 access panels with theft prevention TORX security screws. 
CE marked. Complies with European standard EN 997 for 4L flush.
Weight: 21kg.
10-year warranty.

 

TECHNICAL FEATURES 

MONOBLOCO S21 WC pan with cistern 
Ref. 110390

Height 815mm
Length 620mm
Width 370mm
Thickness 1.5mm
Finish 304 polished satin stainless steel
Артикул: DE-110390 ,   Время доставки: 7 недель
2439,00 €

FM Mattson незамерзающий садовый кран 400мм, с ключом ХОЛОДНАЯ+ГОРЯЧАЯ вода

Garden valve for cold and hot water

  • For cold and hot water
  • With approved non-return valves
  • Can be cut to suit wall thickness
  • Wall bracket: H=70 mm, W=180 mm, screw holes c/c 164 mm
Артикул: 42820050 ,   Время доставки: 7-14 дней
331,55 € (5%)
349,00 €
Антивандалльная душевая пьезо кнопка Н/Р сталь, для смешанной воды,  без адаптора
 
 

AUS 11

Pressure button-controlled shower for heat regulated water

 

 

   
 
 
 

AUS 11 is a new type of shower fitting for single shower control. The fitting is designated for premixed water – with one water inlet and shower outlet elbow. Water is released and closed by an anti-vandal pressure button connected to electronics and an electromagnetic valve. The fitting is covered by a rust-free anti-vandal cover to prevent damage. 

The mounting system has been designed so as to make removing the cover without using tools impossible with no bolt or screw being visible. The cover can be "pushed into" the wall level even if the mount box has been walled to an incorrect depth. 

AUS 11 is identical to AUS 1P with a different design and very resistant cover sheet. 

Electronics can work in two modes: 

1) The button works on the START/STOP basis – water release/closing. If the water is not turned off upon the time adjusted by the user or manager (e.g. 20 seconds), the electronic system itself instructs water stopping. The user must press again to start water running. This significantly saves water as the user reduces the showering time. 

2) The button works on the START/STOP basis. After the time adjusted by the manager (e.g. 3 minutes) expires there is a forced break when water cannot be released. During this time, the user is forced to leave the shower or wait. This prevents needless showering – water wasting. 

 

 
Basic technical information
Water input: G 1/2“
Water pressure: 1 - 10 Bar (0,1 – 1,0 MPa)
Time of water flow: 10 s – 42,5 min in mode 1
  0 s - 42,5 min in mode 2
Power supply: 12 V, 50 Hz
Power requirement: 6 VA
Source of power supplz: ZAC 1/20 (max. 3× AUS 11)
  ZAC 1/50 (max. 8× AUS 11)
Weight: 2,0 kg
 
 
Requirements for setting up the construction
  1. Water installation set up as per picture
  2. Set-up alcove 150 x 75 mm for installation casket
  3. Set-up cable for power supply – 12 V, 50 Hz from source of power supply ZAC
 
 
Complete delivery
  • installation casket
  • input and output bolting
  • electromagnetic valve
  • spherical valve
  • covering metal plate with piezo button
  • electronics
 
 
Made to order
  • SP 1 – shower arm with water flow of 9 l/min
  • SP 2 – shower arm with water flow of 7 l/min
  • SP 3 – shower arm with water flow of 7 l/min
  • ZAC - source of power supply 12V, 50Hz
 
 
Figure
 
 
A - water inlet G 1/2"
C - electricity supply cable 12 V, 50 Hz 
G - water outlet into shower armG 1/2"
 
 
 
 
Download information about the product
AUS 11 data for projectants - ( 84 kB )
 
Артикул: AZP-AUS 11 ,   Время доставки: 3-4 недели
375,00 €

Настенное крепление для инвентаря 3-е, Mop and Broom Holder Н/Р сталь AISI304

DESCRIPTION

 
 
24" (610mm) long. Type 304 stainless steel, satin finish. Anti-slip mop holders have spring-loaded rubber cam that grips handles 7⁄8" to 1 1⁄4" (20–30mm) diameter. Holds 3 mops 3 1⁄4" (85mm) from wall. Height 5" (125mm).
 
 
Артикул: B-223x24 ,   Время доставки: 4-6 недель
232,75 € (5%)
245,00 €