Tootegrupid

Antivandaalne R/V teras piezo dušisi nupp, eelsegatud veele, ilma el.adaptorita

Tootekood: AZP-AUS 11
Kaubamärk:
Ühik: tk
Tarneaeg: 3-4 nädalad
Hind:
312,00 €
Kogus: - +
   - või -   
 
 

AUS 11

Pressure button-controlled shower for heat regulated water

 

 

   
 
 
 

AUS 11 is a new type of shower fitting for single shower control. The fitting is designated for premixed water – with one water inlet and shower outlet elbow. Water is released and closed by an anti-vandal pressure button connected to electronics and an electromagnetic valve. The fitting is covered by a rust-free anti-vandal cover to prevent damage. 

The mounting system has been designed so as to make removing the cover without using tools impossible with no bolt or screw being visible. The cover can be "pushed into" the wall level even if the mount box has been walled to an incorrect depth. 

AUS 11 is identical to AUS 1P with a different design and very resistant cover sheet. 

Electronics can work in two modes: 

1) The button works on the START/STOP basis – water release/closing. If the water is not turned off upon the time adjusted by the user or manager (e.g. 20 seconds), the electronic system itself instructs water stopping. The user must press again to start water running. This significantly saves water as the user reduces the showering time. 

2) The button works on the START/STOP basis. After the time adjusted by the manager (e.g. 3 minutes) expires there is a forced break when water cannot be released. During this time, the user is forced to leave the shower or wait. This prevents needless showering – water wasting. 

 

 
Basic technical information
Water input: G 1/2“
Water pressure: 1 - 10 Bar (0,1 – 1,0 MPa)
Time of water flow: 10 s – 42,5 min in mode 1
  0 s - 42,5 min in mode 2
Power supply: 12 V, 50 Hz
Power requirement: 6 VA
Source of power supplz: ZAC 1/20 (max. 3× AUS 11)
  ZAC 1/50 (max. 8× AUS 11)
Weight: 2,0 kg
 
 
Requirements for setting up the construction
  1. Water installation set up as per picture
  2. Set-up alcove 150 x 75 mm for installation casket
  3. Set-up cable for power supply – 12 V, 50 Hz from source of power supply ZAC
 
 
Complete delivery
  • installation casket
  • input and output bolting
  • electromagnetic valve
  • spherical valve
  • covering metal plate with piezo button
  • electronics
 
 
Made to order
  • SP 1 – shower arm with water flow of 9 l/min
  • SP 2 – shower arm with water flow of 7 l/min
  • SP 3 – shower arm with water flow of 7 l/min
  • ZAC - source of power supply 12V, 50Hz
 
 
Figure
 
 
A - water inlet G 1/2"
C - electricity supply cable 12 V, 50 Hz 
G - water outlet into shower armG 1/2"
 
 
 
 
Download information about the product
AUS 11 data for projectants - ( 84 kB )
 
 
 

AUS 11

автоматический душевой смеситель с кнопкой пьезо 

   
 
 
 

AUS 11 представляет собой новый тип арматуры для душа, предназначенной для управления одним душем. Арматура для работы с предварительно смешанной водой – имеет один привод воды и вывод в плечо душа. Пуск и перекрытие воды осуществляется при помощи антивандальной пьезокнопки, подключенной к электронике и к электромагнитному вентилю. От повреждения арматура покрыта нержавеющим антивандальным кожухом. 

Система крепежа сконструирована так, что кожух невозможно снять без использования инструментов, однако, одновременно с этим, невидно никаких винтов или шурупов. Кожух можно "дожать" до уровня стены даже при замуровывании монтажной коробки на неправильную глубину. 

Устройство AUS 11 похоже, на устройство AUS 1P , но с иным дизайном и весьма прочной жестью кожуха. 

Электроника может работать в двух режимах:

1) Кнопка работает по системе СТАРТ/СТОП - включение/отключение воды. Если бы не произошло отключение воды пользователем, то после истечения настроенного администратором времени (например: 20 секунд) электроника сама даст команду дя остановки воды. Для последующего пуска воды пользователь снова должен нажать на кнопку. Тем самым произойдет значительная экономия воды, так как пользователь ограничит время принятия душа. 

2) Кнопка работает по системе СТАРТ/СТОП. После истечения настроенного администратором времени (например: 3 минуты) произойдет принудительный перерыв, когда вообще не будет возможно пустить воду. В процессе этого времени пользователь принуждается покинуть душевую или ждать. Тем самым будет ограничено избыточно ненужная помывка и бессмысленный расход воды. 

 

 

 
Основные технические характеристики 
Ввод воды: G 1/2“
Давление воды: 0,1 – 1,0 МПа
Настраиваемый период открывания: 10 сек. – 42,5 мин. в режиме 1
  0 сек. – 42,5 мин. в режиме 2
Электропитание: 12 В, 50 Гц
Потребляемая мощность: 6 ВА
Источник питания: ZAC 1/20 (макс. 3× AUS 11)
  ZAC 1/50 (макс. 8× AUS 11)
Вес: 2,0 кг
 
 
Требования к установке
  1. Изготовлена система распределения воды, как показано на рисунке, включая монтаж термостатического вентиля.
  2. Подготовлена ниша 150 x 75 мм для инсталляционной коробки.
  3. Подведен кабель питания – 12 В, 50 Гц от источника ZAC
 
 
Комплектация
  • инсталляционная коробка
  • входное и выходное резьбовые соединения
  • электромагнитный вентиль
  • шаровой вентиль
  • предохранительный монтажный лист
  • электроника
 
 
На заказ
  • SP 1 – душевая лейка с протоком 9 л/мин.
  • SP 2 – антивандальная душевая лейка с протоком 9 л/мин.
  • SP 3 – антивандальная душевая лейка с протоком 9 л/мин.
  • SP 4 - антивандальная душевая лейка с протоком 9 л/мин.
  • SP 5 - антивандальная душевая лейка с протоком 12 л/мин.
  • ZAC - источник питания 12V, 50Hz
 
 
Примечание
 
 
A - ввод воды (Труба G1/2“ внутренняя)
C - ввод электрознергии 12 V, 50 Hz 
G - выход воды к рычажоку 
 
 
 
 
Здесь можно скачать информации по изделиях
AUS 11 Данные для проектировщиков - ( 84 kB )
 
 
Sarnased tooted

Peitsegisti 30 sek töötsükkel

Tootekood: P35941 ,   Tarneaeg: 7-14 päeva
530,00 €

Peitsegisti 30 sek töötsükkel

Tootekood: P35190 ,   Tarneaeg: 7-14 päeva
590,00 €

Peitsegisti 30 sek töötsükkel

Antiblock süsteemiga

Tootekood: P35192 ,   Tarneaeg: 7-14 päeva
625,00 €

Dušhikraan, eelsegatud veele 30 sek töötsükkel

Tootekood: P38222 ,   Tarneaeg: 7-14 päeva
170,00 €
Kokku sobivad tooted

1/2" väliskeere

Tootekood: P29300 ,   Tarneaeg: 7-14 päeva
156,00 €

1/2" väliskeere

Tootekood: P29255 ,   Tarneaeg: 7-14 päeva
140,00 €
 
 

SP 5

tilting shower head - 12 l/min - VANDAL-RESISTANT

   
 
 
 

Design vandal-resistant arm with the flow of 12 litres / minute. The arm has a tilting outlet and an aerator protected against scaling. The arm is protected against theft with a countersunk Allen screw; therefore, it cannot be dismounted without a tool.

Tootekood: AZP-SP5 ,   Tarneaeg: 3-4 nädalad
132,00 €
 
 

ZAC 1/20, ZAC 1/50, ZAC 1/36L

power supply

   
 
 
 

ZAC is a safe source of voltage supply intended to power automatic sanitary equipment made by AZP Brno, Ltd. 

The source of power supply consists of a safety transformer produced in accordance with ČSN IEC 742+A1 standards. All kinds of sensors can be connected to these sources in random combinations, as can other devices with a supply voltage of 12 V, 50 Hz (total power requirement either 20 VA, 50 VA or 36 VA). 

ZAC 1/20 and ZAC 1/50 are independent sources, 1/36L ZAC is the source for the location on the DIN-rail (4 modules).

 

 
Version types
ZAC 1/20 - source of power supply with output 20 VA
ZAC 1/50 - source of power supply with output 50 VA
ZAC 1/36L - source of power supply with output 36 VA
 
Source of power supply can be placed at a maximum distance of 30 m from the connected appliance. 
 
Basic technical information
Input voltage: 230 V, 50 Hz
Output voltage: 12 V, 50 Hz
Power requirement: 20 VA (ZAC 1/20)
  50 VA (ZAC 1/50)
  36 VA (ZAC 1/36L)
Electricity protection: IP 55 (ZAC 1/20, ZAC 1/50)
  IP 20 (ZAC 1/36L)
Weight: 0,8 kg (ZAC 1/20, ZAC 1/36L)
  1,2 kg (ZAC 1/50)
 
 
Requirements for setting up the construction
ZAC 1/20, ZAC 1/50
  1. Set-up supply of electricity 230 V,50 Hz – cable CYKY 3Cx1,5
  2. Set-up niche for flush mounting – size as per installed source
  3. Distribution to each device is carried out by cable CYKY 2Ax1,5
ZAC 1/36 L
  1. It is installed on the DIN-rail - width of 4 modules
 
 
Figure
ZAC 1/20
 
ZAC 1/50
 
 
 
 
 
Product title
ZAC 1/20 - 
power supply for up to 3 devices - 230V, 50Hz
ZAC 1/50 - 
power supply for up to 8 devices - 230V, 50Hz
ZAC 1/36L - 
power supply for up to 6 devices - 230V, 50Hz
Tootekood: AZP-ZAC 1-20 ,   Tarneaeg: 3-4 nädalad
90,00 €
Sarnased tooted
On võimalik versioonid , vertikaalsed, horisontaalsed D50mm,75mm,110mm
 
 
 
 

PV 01

stainless steel floor trap

   
 
 
 

PV 01 is a fully stainless floor trap with braz designed to drain showers, industrial premises and other inner spaces. The trap is designed as stepping (not driven-over). The trap is made of AISI 304 quality stainless steel. Detergents containing chlorine must not be used for cleaning. If chlorine is contained in the environment, we recommend custom-made model of another material (e.g. AISI 316).

For cleaning we recomnned WÜRTH detergents – material preservation (no. 0893 121 K) and material cleaning (no. 893 121 1). 

We produce other custom-made models – outlet d = 50 mm, 110 mm; without rim for waterproofing; alternative cover grid (mesh); without braz; with adjustable height, etc. Send us your requirements, we will promptly answer!

 

Version types
PV 01.D.75.P - floor trap d = 75 mm, smell trap, outlet down, rim for waterproofing, not adjustable
PV 01.D.75.S - floor trap d = 75 mm, smell trap , outlet down , rim for waterproofing, adjustable
PV 01.B.75.P - floor trap d = 75 mm, smell trap , outlet to the side, rim for waterproofing, not adjustable
PV 01.B.75.S - floor trap d = 75 mm, smell trap , outlet to the side , rim for waterproofing , adjustable
PV 01.D.50.P - floor trap d = 50 mm, smell trap , outlet down , rim for waterproofing , not adjustable
PV 01.D.50.S - floor trap d = 50 mm, smell trap , outlet down , rim for waterproofing , adjustable
PV 01.B.50.P - floor trap d = 50 mm, smell trap , outlet to the side , rim for waterproofing , not adjustable
PV 01.B.50.S - - floor trap d = 50 mm, smell trap , outlet to the side , rim for waterproofing , adjustable
PV 01.D.110.P - floor trap d = 110 mm, smell trap , outlet down , rim for waterproofing , not adjustable
PV 01.D.110.S - floor trap d = 110 mm, smell trap , outlet down , rim for waterproofing , adjustable
PV 01.B.110.P - floor trap t d = 110 mm, smell trap , outlet to the side , rim for waterproofing , not adjustable
PV 01.B.110.S - floor trap d = 110 mm, smell trap , outlet to the side , rim for waterproofing , adjustable
 
 
Basic technical information
Minimum inner diameter: 70 mm
Diameter of connecting sewerage pipe: 75 mm
Water flow: min. 50 lts / min
Loading class: K3
Weight: 2,2 kg
 
 
Complete delivery
  • Trap body
  • Grid with braz cover
  • Hook to pull up the grid
 
 

 

Requirements for setting up the construction
  1. Completed sewerage drains terminated by DN 75 coupling
  2. Prepared hole in the floor with diameter min. 300 mm (200 mm without rim for waterproofing) and depth min. 120 mm
 
Tootekood: AZP-PV 01.D.75.P ,   Tarneaeg: 3-4 nädalad
342,00 €

TECHNICAL FEATURES

LISO urinal divider for wall-mounting 
Ref. 100590

Height 700mm
Length 25/50mm
Width 350mm
Thickness 1.5mm
Finish 304 polished satin stainless steel
Tootekood: DE-100590 ,   Tarneaeg: 14-30 päeva
555,00 €

> Working pressure :

1 to 5 bar

> Flow :

10 l/min with integrated flow limiter
Hand-held shower on rail with chrome plated slide

> Hydraulic supply :

G 1/2" (15x21), top or rear water inlet. For rear water inlet, we recommend to use the adaptation kit under the reference 91026. On single control mixer tap with ceramic disks

> Material :

Anodised aluminium extruded section (2.5mm thickness) Aluminium removable valve plate, peinted RAL 7005 colour High resistance RAL 7005 coloured ABS covers

> Functioning:

Wide opening panel without the need to dismantle from the wall and shower taps on a removable valve plate

> Thermal resistance :

Resistant to a temperature of 75°C for 30-minute-thermal-shocks

> Security :

Adjustable tamper-proof temperature limiter to prevent scalding

> Delivered with :

1/2" hoses with revolving nuts
MM 1/2" (15x21) straight stop valves and 250 micron filters Fastening screws and instruction manual

> Standards & approvals :

Brass body in accordance with EN 1982, EN 12164, EN 12165 Chrome-plated surface treatment in accordance with EN 12540 200-hour neutral salt spray resistant (NSS) in accordance with ISO 9227

Tootekood: P88818 ,   Tarneaeg: 14-21 päeva
945,25 € (5%)
995,00 €

Splashback 2400mm for CANAL wash trough 
Ref. 100300

Splashback for CANAL wash trough.
Bacteriostatic 304 stainless steel.
Polished satin finish.
Stainless steel thickness: 1.2mm.
Length: 2,400mm. 

 

TECHNICAL FEATURES

Splashback 2400mm for CANAL wash trough 
Ref. 100300

Height 300mm
Length 2400mm
Width 1.5mm
Thickness 1.2mm
Finish 304 polished satin stainless steel
Tootekood: DE-100300 ,   Tarneaeg: 14-21 päeva
345,00 €

DRINKING SYSTEM

  • Frost-free drinking system for cattle and horses
  • Fresh and clean water for the animals all year round
  • Without wiring or electricity 
  • A minimum of maintenance
  • No concern about filling the drinking vessels
  • No concern about cleaning the drinking vessels
 
Automaatjootjad sobivad kasutamiseks nii karjamaal kui ka tallides ning nende läheduses asuvates joogikohtades.
Jootjaid on lihtne kasutada ning hobused saavad kiiresti aru, et mugavam on vee juurdevoolu avamiseks vajutada klapile
mitte nina otsaga vaid selle ülaosaga. Kui koon (mokad) on joomiseks vabad, joobki hobune loomulikul viisil vee pindmiselt
kihilt. Seetõttu olemegi valinud jooginõuks lai ja sügav kauss, et tekiks joomiseks mugav veepind.
 
Töötamise põhimõte
Tõusutoru on varustatud isetühjeneva 3-tee
ventiiliga, mis on paigaldatud kaevu, mis omakorda
on süvistatud pinnasesse.
Kui jootjat ei kasutata on veest tühi nii ventiil kui
ka tõustoru, milles olev vesi võiks muidu külmuda.
Nii jootja ventiil ja tõusutoru on külmumiskindlad nii
kaua kuni on külmumiskindel ka vee toitetorustik.
 
 
Tootekood: FL-A362 ,   Tarneaeg: 14-21 päeva
845,10 € (10%)
939,00 €