Tootegrupid
AFO-02-ii.jpg Zoom

Joogifontään free-standing mehaaniline R/V teras AISI304

Tootekood: AZP-AFO02
Kaubamärk:
Ühik: tk
Tarneaeg: 3-4 nädalad
Hind:
1531,00 €
Kuumakse alates: 130,14 €
Kogus: - +
   - või -   

Joogifontään free-standing mehaaniline R/V teras AISI304

AFO 02 - IIstainless steel free-standing drinking fountain (indoor/outdoor)

AFO 02-II is a stainless steel drinking fountain of modern design with a manual press valve that allows its easy use. The water flows only when the valve is pressed and then there is a certain adjusted time to rinse out the nozzle.
The drinking fountain is to be placed in an open space. It is made up of an anchoring part intended for embedding in concrete and the column itself with a press valve and nozzle. These parts are connected by means of 3 screws and the upper part can be, therefore, easily dismounted in case of necessity (e.g. during winter).
The water inlet is fitted with a flexible hose, the siphon is made from a stretchy, flexible connector. The flexible finish of the water inlet and outlet allows the variable and problem-free connection of the fountain.
AFO 02-II stainless steel fountain is suitable mainly for schools, medical facilities and spa resorts, and is utilizable outdoors.
Drinking fountain AFO 02-II is manufactured from the stainless steel AISI 304. AFO 02.CL-II is made of the stainless steel AISI 316 and is suitable for places with higher concentration of chlorine.
For cleaning we recomnned WÜRTH detergents – material preservation (no. 0893 121 K) and material cleaning (no. 893 121 1).Detail of the bowl

Package contents

  • stainless steel column and cone with nozzle
  • press valve
  • anchoring construction
  • flexible hose siphon
  • connecting hoses
  • anchoring material
  • Set-up water inlet - pipe G 1/2“
  • Set-up drainage d = 40 mm
  • Prepared alcove for embedding (concreting) in the base construction
Water inlet G 1/2"
Water pressure 2 – 6 Bar, recommended 3 Bar
Outlet d = 40 mm
Inner dimensions of sink d = 290 mm
Weight 20 kg
 
Sarnased tooted

Liivapüüdur SAND-02 Elcee 220, 3,5L, R/V teras, AISI304

Kasutusjuhend:

Liivapüüdur SAND-02 Elcee 220, 3,5L, roostevaba teras, AISI304

Liivapüüdur SAND-02 Elcee 220 on mõeldud liiva filtreerimiseks veest ning selle maht on 3,5 liitrit. Seade on valmistatud roostevabast terasest (AISI304) ja on ideaalne paigaldamiseks otse kraanikausi või valamualuse alla.

Paigaldamine:
Liivapüüdur on lihtne paigaldada otse kraanikausi või valamualuse alla, kasutades selleks sobivaid kinnitusvahendeid.

Kasutamine:
Liiv ja mustus kogunevad seadme alumisse kaussi. Seadme efektiivse töö tagamiseks on vajalik kaussi regulaarselt tühjendada.

Hooldus:
Kauss on kinnitatud korpuse külge kahest küljest kinnitustega. Kaussi puhastamiseks eemaldage see kinnitustest, tühjendage ja vajadusel puhastage.

Üldmõõtmed millimeetrites: Ø174 x 235

Sissevoolu mõõtmed millimeetrites: 1,5"

Väljavoolu mõõtmed millimeetrites: 1,5"

Materjal: AISI 304

Materjali paksus millimeetrites: 1,5

Kogukaal kilogrammides: 2,50

 

Wash trough acc. Separator SAND-02

Description

The sand catcher has a capacity of 3,5 litres and is ideal for filtering sand from water.
It is easy to mount directly under a washbasin or a wash trough.

The sand catcher is delivered with a flexible outlet that will enable straight or bent installation possibilities.

Material: Stainless steel AISI 304

 

Overall dimension in mm Ø174 x 235

Inlet dimension in mm 1.5"

Outlet dimension in mm 1.5"

Material AISI 304

Material thickness in mm 1.5

Gross weight in kg 2.50

Tootekood: I-SAND-02 ,   Tarneaeg: 3-4 nädalad
469,00 €

AUM 026 INV is a stainless steel, partly wall-built in washbasin, containing the combination of a liquid soap dispenser, water tap and hand dryer in a small space. The washbasin is adjusted to be used also by wheelchair persons – it is shallow, completed with handles, the waste is hidden behind the wall. Controlled by durable piezo-pushbuttons, electronically controlled turn-off (the period of water running is settable by the owner). The washbasin is to be mounted through the wall, all technology components are behind the wall, and thus cannot be damaged by users (anti-vandal design).

A wall-hanged version may be supplied to order, or a version without any of the functions (e.g. onlz water plus soap, or water plus dryer). The washbasin is made of AISI 304 stainless steel. A recommended cleaning agent for stainless products maintenance: Würth – preservation (order no. 0893 121 K), cleaning (order no. 893 121 1).

Basic technical information
Power supply: 230 V, 50 Hz
IP protection: IP 55
Dimensions (visible from outside): 800 x 800 x 363 mm
Required thickness of wall: min. 100 mm
Outlet: d = 40 mm
 
Requirements for setting up the construction
  1. Opening in the wal 740 x 740 mm
  2. Prepared el. supply cable 3C x 1,5 s 230 V, 50 Hz
  3. Prepared water outlet according to technical scheme
 
 
Complete delivery
  • Stainless-steel washbasin with handles
  • Electronic hand dryer
  • Electronic soap dispenser
  • Electronic water tap
  • Through-wall frame with bolts
  • Waste with a stink trap
  • 230V / 12V source for the electronics
 
Tootekood: AZP-AUM 026.TV INV ,   Tarneaeg: 3-4 nädalad
4300,00 €
Antivandaalne R/V teras piezo dušisi nupp, eelsegatud veele,  ilma el.adaptorita
 
 

AUS 11

Pressure button-controlled shower for heat regulated water

 

 

   
 
 
 

AUS 11 is a new type of shower fitting for single shower control. The fitting is designated for premixed water – with one water inlet and shower outlet elbow. Water is released and closed by an anti-vandal pressure button connected to electronics and an electromagnetic valve. The fitting is covered by a rust-free anti-vandal cover to prevent damage. 

The mounting system has been designed so as to make removing the cover without using tools impossible with no bolt or screw being visible. The cover can be "pushed into" the wall level even if the mount box has been walled to an incorrect depth. 

AUS 11 is identical to AUS 1P with a different design and very resistant cover sheet. 

Electronics can work in two modes: 

1) The button works on the START/STOP basis – water release/closing. If the water is not turned off upon the time adjusted by the user or manager (e.g. 20 seconds), the electronic system itself instructs water stopping. The user must press again to start water running. This significantly saves water as the user reduces the showering time. 

2) The button works on the START/STOP basis. After the time adjusted by the manager (e.g. 3 minutes) expires there is a forced break when water cannot be released. During this time, the user is forced to leave the shower or wait. This prevents needless showering – water wasting. 

 

 
Basic technical information
Water input: G 1/2“
Water pressure: 1 - 10 Bar (0,1 – 1,0 MPa)
Time of water flow: 10 s – 42,5 min in mode 1
  0 s - 42,5 min in mode 2
Power supply: 12 V, 50 Hz
Power requirement: 6 VA
Source of power supplz: ZAC 1/20 (max. 3× AUS 11)
  ZAC 1/50 (max. 8× AUS 11)
Weight: 2,0 kg
 
 
Requirements for setting up the construction
  1. Water installation set up as per picture
  2. Set-up alcove 150 x 75 mm for installation casket
  3. Set-up cable for power supply – 12 V, 50 Hz from source of power supply ZAC
 
 
Complete delivery
  • installation casket
  • input and output bolting
  • electromagnetic valve
  • spherical valve
  • covering metal plate with piezo button
  • electronics
 
 
Made to order
  • SP 1 – shower arm with water flow of 9 l/min
  • SP 2 – shower arm with water flow of 7 l/min
  • SP 3 – shower arm with water flow of 7 l/min
  • ZAC - source of power supply 12V, 50Hz
 
 
Figure
 
 
A - water inlet G 1/2"
C - electricity supply cable 12 V, 50 Hz 
G - water outlet into shower armG 1/2"
 
 
 
 
Download information about the product
AUS 11 data for projectants - ( 84 kB )
 
Tootekood: AZP-AUS 11 ,   Tarneaeg: 3-4 nädalad
375,00 €

Valamu R/V terasest

Garaazi/koristusruumi jaoks

Tootekood: I-U1STD ,   Tarneaeg: 7-14 päeva
329,00 €

Joogifontään põranda/sein mehaaniline R/V teras AISI304

AFO 01.S

stainless steel drinking fountain with pressure valve designed to stand and to be attached to wall

AFO 01.S is a drinking fountain of stainless steel with pressure valve designed to stand and to be attached to wall. Water runs for the time for which the valve is pressed plus the pre-set period after it is released; thus the jet can be rinsed.
Water supply is provided by a flexible hose, trap comprises an elastic flexible couple. Flexible design of water supply and outflow allows variable and easy connection of the drinking fountain as well as its dismounting.

Automatic drinking fountain (with a sensor) can be supplied per order.

AFO 01.S is manufactured from the stainless steel AISI 304. Other materials (e.g. AISI 316) possible on order. For cleaning we recomnned WÜRTH detergents – material preservation (no. 0893 121 K) and material cleaning (no. 893 121 1). 

Package contents

  • Stainless housing with cone
  • Pressure valve with jet
  • Flexible hose outflow
  • Fixing and connecting material
dimensions 330 x 900 x 365 mm
outlet d = 40 mm
water inlet G 1/2"
water pressure 0,2 – 0,6 MPa, recommended 0,3 MPa
weight 12 kg

 

  • Set up water outlet d = 40 mm
  • Set up water inlet G 1/2"
Tootekood: AZP-AFO01.S ,   Tarneaeg: 3-4 nädalad
1226,00 €
Projektide hinnapäringud ja tooteinfo kättesaadavusega seotud küsimused palume saata e-mailile info@pegu.ee