Water inlet | G 1/2" |
Water pressure | 0,2 – 0,6 MPa (recommended 0,3 MPa) |
Outlet | d = 40 mm |
Inner dimension of the fountain | d = 245 mm |
Weight | 4 kg |
Müüja: PEGU OÜ
Kasuta sooduskoodi ja saa soodustust tootele, mis ei osale muudes Maikuu kampaaniates!
✔ Allahindlus ainult Mai kuu jooksul – kiirusta!
✔ Kvaliteetne toode mugavalt ja turvaliselt otse koju
✔ Professionaalne teenindus ja läbipaistev ostukeskkond
Lisa toode ostukorvi, sisesta seal kood PEGU-KEVAD2025 ja saa soodustus toodetele, mis ei kuulu teistesse sama perioodi kampaaniatesse.
Ainult mais – kasuta võimalust, enne kui kampaania lõpeb!
PEGU.ee – tark valik neile, kes hindavad disaini, kvaliteeti ja nutikat ostlemist.
500x490x300
R/V teras AISI 304
MONOBLOCO S21 WC pan with cistern
Ref. 110390
Floor-standing WC pan with dual flush cistern 3L/6L, 370 x 815 x 620mm.
Bacteriostatic 304 stainless steel. Polished satin finish.
Stainless steel thickness: 1.5mm.
One-piece pressed WC bowl, seam-free for better hygiene.
WC bowl surface is polished with rounded edges for easy cleaning.
Concealed perimetral flushing rim. Water supply can be recessed from below or exposed from the side (right/left).
Recessed horizontal or vertical waste outlet. Supplied with PVC pipe.
Pre-drilled holes for fixing the toilet seat. Supplied with stainless steel blanking caps when installed without toilet seat lid.
Quick to install: 2 access panels with theft prevention TORX security screws.
CE marked. Complies with European standard EN 997 for 4L flush.
Weight: 21kg.
10-year warranty.
MONOBLOCO S21 WC pan with cistern
Ref. 110390
Height | 815mm |
---|---|
Length | 620mm |
Width | 370mm |
Thickness | 1.5mm |
Finish | 304 polished satin stainless steel |
Delabie Valamu HEMI d310mm AISI304 poleeritud roostevaba teras
HEMI inset round washbasin Ø 310mm - Ref. 120471
Round basin for recessed installation from above or below.
Basin internal diameter: 310mm.
Cut-out diameter: 330mm for installation from above, 310mm for installation from below.
Bacteriostatic 304 stainless steel.
304 stainless steel, bright polished
Stainless steel thickness: 1mm. One-piece, seam-free pressed bowl.
Rounded edges prevent injury. Supplied with 1¼" waste. Without overflow.
CE marked.
Complies with European standard EN 14688. Weight: 1.5kg.
AFO 01 is a stainless steel wall-mounted drinking fountain of modern design with a manual press valve that allows its easy use. The water flows only when the valve is pressed and then there is a certain adjusted time to rinse out the nozzle.
The water inlet is fitted with a flexible hose, the siphon is made from a stretchy, flexible connector. The flexible finish of the water inlet and outlet allows the variable and problem-free connection of the fountain.
AFO 01 stainless steel fountain is suitable mainly for schools, medical facilities and spa resorts, and is utilizable outdoors.
AFO 01 is made of stainless steel AISI 304.
AFO 01.CL is made of stainless steel AISI 316 and is suitable into the areas with higher concentration of chlorine (e.g. swimming pools).
Sensor-controlled fountain possible made to order.
For cleaning we recomnned WÜRTH detergents – material preservation (no. 0893 121 K) and material cleaning (no. 893 121 1).
Water inlet | G 1/2" |
Water pressure | 0,2 – 0,6 MPa (recommended 0,3 MPa) |
Outlet | d = 40 mm |
Inner dimension of the fountain | d = 245 mm |
Weight | 4 kg |
> Working pressure : 1 to 5 bar
> Flow : 6 l/min at 3 bar - 4-position flow adjustment device Anti-water-hammering design
> Flow time : 15 seconds (± 5 sec.)
> Hydraulic supply : In-line water inlet M G 1/2" Inlet and outlet Cold water
> Thermal resistance : Resistant to a temperature of 75°C for 30 minute thermal shock
> Security : Patented anti-blocking "S" system to avoid the water to flow continuously
> Delivered with : 1 Cross-partition control (1 to 200 mm thick) 1 Short wall spout (Non-rotating fixing) 87 mm 1 Closing tap with S anti-blocking system 1 stop valve M 1/2" (15x21) / M 1/2" (15x21) with quick couplings (12x14 mm) Instruction manual
> Standards & approvals : Brass body in accordance with EN 1982, EN 12164, EN 12156 Molded chrome-plated body in accordance with EN 12540 200-hour neutral salt spray resistant (NSS) in accordance with ISO 922
Semi-recessed QUADRA washbasin
Ref. 120650
Semi-recessed washbasin, 380x380mm.
Suitable for use with wall-mounted or extended mixer/tap.
Basin internal diameter: 310mm.
Cutout diameter: 310mm.
Stainless steel thickness: 1.2mm.
Polished satin finish.
Stainless steel thickness: 1.2mm.
One-piece, seam-free pressed bowl.
Rounded edges prevent injury.
Supplied with 1¼" waste.
Without overflow.
CE marked. Complies with European standard EN 14688.
Weight: 3kg.
Semi-recessed QUADRA washbasin
Ref. 120650
Height | 130mm |
---|---|
Length | 380mm |
Width | 380mm |
Thickness | 1.2mm |
Finish | Polished satin 304 stainless steel |