Tootegrupid

Aasia WC

Tootekood: PPT
Kaubamärk:
Ühik: tk
Tarneaeg: 7-21 päeva
Hind: 347,35 €
312,62 €
Kogus: - +
   - või -   

Aasia WC, R/V teras AISI 304

Kokku sobivad tooted

WC isesulguv mehhanism

Tootekood: P14906 ,   Tarneaeg: 7-21 päeva
218,84 € (10%)
243,16 €

Pissuaari isesulguv mehhanism

Tootekood: P38336 ,   Tarneaeg: 7-21 päeva
160,20 € (10%)
178,00 €
Sarnased tooted

Overall dimension in mm Ø174 x 235 Inlet dimension in mm 1.5" Outlet dimension in mm 1.5" Material AISI 304 Material thickness in mm 1.5 Gross weight in kg 2.50

Tootekood: EL220-1080020 ,   Tarneaeg: 3-4 nädalad
375,00 €
 
 

AUS 11

Pressure button-controlled shower for heat regulated water

 

 

   
 
 
 

AUS 11 is a new type of shower fitting for single shower control. The fitting is designated for premixed water – with one water inlet and shower outlet elbow. Water is released and closed by an anti-vandal pressure button connected to electronics and an electromagnetic valve. The fitting is covered by a rust-free anti-vandal cover to prevent damage. 

The mounting system has been designed so as to make removing the cover without using tools impossible with no bolt or screw being visible. The cover can be "pushed into" the wall level even if the mount box has been walled to an incorrect depth. 

AUS 11 is identical to AUS 1P with a different design and very resistant cover sheet. 

Electronics can work in two modes: 

1) The button works on the START/STOP basis – water release/closing. If the water is not turned off upon the time adjusted by the user or manager (e.g. 20 seconds), the electronic system itself instructs water stopping. The user must press again to start water running. This significantly saves water as the user reduces the showering time. 

2) The button works on the START/STOP basis. After the time adjusted by the manager (e.g. 3 minutes) expires there is a forced break when water cannot be released. During this time, the user is forced to leave the shower or wait. This prevents needless showering – water wasting. 

 

 
Basic technical information
Water input: G 1/2“
Water pressure: 1 - 10 Bar (0,1 – 1,0 MPa)
Time of water flow: 10 s – 42,5 min in mode 1
  0 s - 42,5 min in mode 2
Power supply: 12 V, 50 Hz
Power requirement: 6 VA
Source of power supplz: ZAC 1/20 (max. 3× AUS 11)
  ZAC 1/50 (max. 8× AUS 11)
Weight: 2,0 kg
 
 
Requirements for setting up the construction
  1. Water installation set up as per picture
  2. Set-up alcove 150 x 75 mm for installation casket
  3. Set-up cable for power supply – 12 V, 50 Hz from source of power supply ZAC
 
 
Complete delivery
  • installation casket
  • input and output bolting
  • electromagnetic valve
  • spherical valve
  • covering metal plate with piezo button
  • electronics
 
 
Made to order
  • SP 1 – shower arm with water flow of 9 l/min
  • SP 2 – shower arm with water flow of 7 l/min
  • SP 3 – shower arm with water flow of 7 l/min
  • ZAC - source of power supply 12V, 50Hz
 
 
Figure
 
 
A - water inlet G 1/2"
C - electricity supply cable 12 V, 50 Hz 
G - water outlet into shower armG 1/2"
 
 
 
 
Download information about the product
AUS 11 data for projectants - ( 84 kB )
 
Tootekood: AZP-AUS 11 ,   Tarneaeg: 3-4 nädalad
254,00 €
 
 

ZAC 1/20, ZAC 1/50, ZAC 1/36L

power supply

   
 
 
 

ZAC is a safe source of voltage supply intended to power automatic sanitary equipment made by AZP Brno, Ltd. 

The source of power supply consists of a safety transformer produced in accordance with ČSN IEC 742+A1 standards. All kinds of sensors can be connected to these sources in random combinations, as can other devices with a supply voltage of 12 V, 50 Hz (total power requirement either 20 VA, 50 VA or 36 VA). 

ZAC 1/20 and ZAC 1/50 are independent sources, 1/36L ZAC is the source for the location on the DIN-rail (4 modules).

 

 
Version types
ZAC 1/20 - source of power supply with output 20 VA
ZAC 1/50 - source of power supply with output 50 VA
ZAC 1/36L - source of power supply with output 36 VA
 
Source of power supply can be placed at a maximum distance of 30 m from the connected appliance. 
 
Basic technical information
Input voltage: 230 V, 50 Hz
Output voltage: 12 V, 50 Hz
Power requirement: 20 VA (ZAC 1/20)
  50 VA (ZAC 1/50)
  36 VA (ZAC 1/36L)
Electricity protection: IP 55 (ZAC 1/20, ZAC 1/50)
  IP 20 (ZAC 1/36L)
Weight: 0,8 kg (ZAC 1/20, ZAC 1/36L)
  1,2 kg (ZAC 1/50)
 
 
Requirements for setting up the construction
ZAC 1/20, ZAC 1/50
  1. Set-up supply of electricity 230 V,50 Hz – cable CYKY 3Cx1,5
  2. Set-up niche for flush mounting – size as per installed source
  3. Distribution to each device is carried out by cable CYKY 2Ax1,5
ZAC 1/36 L
  1. It is installed on the DIN-rail - width of 4 modules
 
 
Figure
ZAC 1/20
 
ZAC 1/50
 
 
 
 
 
Product title
ZAC 1/20 - 
power supply for up to 3 devices - 230V, 50Hz
ZAC 1/50 - 
power supply for up to 8 devices - 230V, 50Hz
ZAC 1/36L - 
power supply for up to 6 devices - 230V, 50Hz
Tootekood: AZP-ZAC 1-20 ,   Tarneaeg: 3-4 nädalad
70,75 €

Kätepesuvalamu Endura ED1

 
 
600x415x130 mm
Tootekood: I-ED1 ,   Tarneaeg: 14-21 päeva
287,76 € (12%)
327,00 €

GENOU wall-mounted hand washbasin

 

 

Reference: 180330

 

CCTP description

Wall-mounted, knee-operated hand washbasin.

Bacteriostatic 304 stainless steel. Polished satin finish.

Stainless steel thickness: 1.2mm

Rounded edges prevent injury.

Supplied with swan neck spout and time flow

tap with 7 second time flow.

Supplied with 1 ¼" waste.

Without overflow.

Supplied with fixing elements.

CE marked. Complies with European standard EN 14688.

Weight: 5kg.

 

Tootekood: DE-180330 ,   Tarneaeg: 14 päeva
765,00 €